This Stock is solid although the point of aim shifted approx .6 mil after installation.
I discovered that the magazine contacted the stock in the rear of the mag well, I could feel the action rocking in the stock.
After relieving the mag well, torquing the action screws per instructions and firing two fouler rounds the rifle placed the next four rounds in a single hole at 100 yards.

Great product and fast shipment

Beautiful, exactly what I was looking for to compliment a lightweight hunter build.

Great products and customer support. Quality of items great and provide instructions for installation.

Great stock for the money. I bought this to replace the flimsy stock that came on an old model 112 flat back single shot with a heavy barrel. The aluminum bedding v block is very solid. No more forearm flex and plenty of barrel float.

An excellent upgrade over my plastic stock. Couldn't be happier. It's high quality all the way, and everything I expected with no disappointments. I did a lot of research before spending my money on this stock, and some have reported problems with it being too tight and not fitting well. I had no issues whatsoever sliding it onto my mil spec buffer tube. I did, however, loosen the front screw before installing. I read that it acts as a tensioner and that is what I experienced too. Loosen before sliding it on, then simply tighten until it's just loose enough to slide back and forth with no play. Perfect fit at that point.

Took a little figuring out,but I got some tech support and got it installed...feels like a different gun..Very nice accessory.

I purchased this for a CZ 527, not a Howa. Just took a chance it was going to be adaptable, and it was. My CZ 527 has the older forged bolt handle, not the later MIM type, so the knob diameter is about .700", not the latest .750". This add on knob actually fits well although the CZ shank is rectangular instead of round. I left out the o-rings, and added a bit of dark hardening filler to fill in the gaps between the rectangular handle shank and knob hole so I cannot see any gaps. This handle has the correct feel and look for my rifle.

the easiest way to fasten this knob so it does not spin around is to add a few layers of teflon plumbing joint tape to the bolt knob then fasten the 2 halves together. you get a good snug seal and easy removal if the knob is removed

Fits Weatherby Vangaurd series 1 & 2 as well - nice addition.

Awesome transaction. Quick delivery and got exactly what I paid for.

Great product, fit perfectly and the finish is beautiful

I’ve used the TacOps ammo cheek piece on all my rifles for years. Great product.

Nice looking bolt knob.

just what i needed to balance the bolt out

This item is what I needed for a new Accustock. Works fine.

I purchased this titanium bolt handle and an improvement over the stock savage bolt handle.
This long action I am building is so smooth now and the titanium bolt handle with the black knob looks awesome together
I will buy another one for my other savage rifles

I purchased this for a CA MPR, it’s a perfect match to the gun and still allows you to fold the stock, looks like a factory part, I was extremely happy with my purchase from Tactical Works.

Very simple design that works well.

Great fit and finish, easy install, no fitting needed. Much easier to manipulate the bolt with gloves on in the deer woods. I would say it’s well worth the money for sure. Tac works shipping is also blazing fast. Thank you

This is what I’ve been wanting for as long as I’ve been shooting. No more squeeze bag. This thing is super find adjustable and SMOOTH! Highly recommended! I have a myopathy in my hand and this is a life saver. Had my shooting partner tried it out and he was sold after the first shot. Quality is first rate and installation took 10 minutes.

Very understanding company. I ordered the wrong part and they gladly issued a full refund.

I think its great. Works like it should.

I built a lightweight 300WM and wanted a low profile bolt knob and this knob fit the ticket.

It fit snug and fit flush without use of o-rings. It was tight and secure and added just enough length to the handle to be what I needed. Well worth the money